PAGE 1
P Series OPERATOR’S MANUAL Covers HK P2000, P2000SK, P30, P30L, P30S, P30LS series pistols (all calibers and variants)
PAGE 2
SAFETY RULES Please read this operator's manual before handling your firearm. The following safety rules are placed in this manual by HK as an important reminder that firearm safety is your responsibility. Firearms can be dangerous and can potentially cause serious injury, damage to property or death, if handled improperly. 1. Never point a firearm at anyone or in any direction other than a SAFE direction, i.e. down range. 2. Treat all firearms as if they are always loaded. 3.
PAGE 3
TABLE OF CONTENTS Safety Precautions & Clearing.......................................................... Inside Cover Section 1 Introduction.......................................................................................5 Section 2 Nomenclature..................................................................................10 Specifications...................................................................................12 Section 3 Function & Operation . ......................................
PAGE 4
A set of easy-to-install modular back straps allow the P30 and P30L pistols to be customfitted to any shooter’s hand. The P30 also incorporates interchangeable side panels for optimal fit. Ambidextrous slide release levers and magazine release levers make handling the P Series pistol natural and easy for right and left-handed shooters.
PAGE 5
DA/SA variant will revert to the single-action mode on each shot unless the operator physically deco*cks the hammer by way of the deco*cking lever. On the double-action/single-action variant, pulling the trigger will co*ck the hammer and immediately release it firing the first chambered cartridge. All subsequent cartridges will be fired in the single-action mode because the slide automatically reco*cks the hammer after each shot is fired.
PAGE 6
section 2 Nomencalture Figure 3A P2000 (left side view) Figure 4A P30 (right side view) Figure 3B P2000 SK (right side view) Figure 4B P30L (left side view) Inset of P30S (with safety lever and deco*cker) 10 11
PAGE 7
P2000 Specifications ________________________________________________________________________________ Caliber Operating Principle Action Type .40 S&W, .357 SIG Short recoil, modified Browning type, linkless 9mm x 19 Short recoil, modified Browning type, linkless ________________________________________________________________________________ Sights Total Length Barrel Length Barrel Profile Sight Radius Twist Length Three dot, fixed patridge style, drift adjustable 173mm (6.81 in.) 93mm (3.66 in.
PAGE 8
SECTION 3 FUNCTION AND Operation Clearing WARNING: Always clear the pistol before handling it. Clearing the Pistol - The P Series pistol is not considered “clear” or safe unless: 1. The safety/control lever (if present) is on “SAFE” and; 2. The magazine is removed from the pistol; 3. The slide is locked to the rear and; 4. The chamber is free of brass or ammunition. To Clear the HK P Series pistol: 1.
PAGE 9
Ambidextrous Slide Release - A slide release lever is located on both the left and right side of the frame directly above the trigger. These levers are used to lock the slide open, to release the slide, and to disassemble the pistol. As a slide stop, it is lifted upward by the magazine follower or the operator's finger as the slide travels rearward during recoil or manual manipulation. The slide release engages in the recess located on the left side of the slide at its midpoint.
PAGE 10
SECTION 5 INSTRUCTIONS FOR USE Filling and Emptying the Magazine NOTE: Do not attempt to load more than the prescribed number of cartridges into the magazine. Do not alter the shape of the magazine housing, follower or spring. To do so may cause stoppages or the magazine may not seat properly in the pistol. 3. Chamber a cartridge - Chamber a cartridge by depressing the slide release or by pulling the slide fully to the rear and releasing it. Do not ride the slide forward! 4.
PAGE 11
If the pistol fails to fire, clear and disassemble it and check for: 1. Obstructions in the chamber, bore or frame. Remove obstructions. 2. Bad ammunition. Try new ammunition. 3. Damaged magazine. Replace magazine. 4. Fouling or lack of lubrication. Clean and lubricate the pistol in accordance to the instructions contained within this manual. 5. Evidence of severely worn or broken parts. Contact HK or your unit armorer.
PAGE 12
Backstrap installation for all P Series pistols - Ensure the hammer strut and hammer spring are properly positioned on the back of the frame (Figure 9). Place the replacement grip panel on the back of the frame, approximately 1 inch (2.54cm) lower than its assembled position (Figure 10), and push the grip panel up onto the grip rails. Figure 9 Figure 10 Continue pushing the grip panel upward on the frame.
PAGE 13
SECTION 6 DISASSEMBLY AND ASSEMBLY Clear the pistol by following the directions on the inside cover Disassembly (Field Stripping) of P2000/P2000 SK pistol 1. Make sure the pistol is CLEAR. 2. Depress the slide release and allow the slide to move forward. 3. Using the firing hand, retract and hold the slide to the rear so that the axle of the slide release is visible through the recess in the left side of the slide (see Figure 15). 4.
PAGE 14
Figure 19 NOTE: Disassembly of the pistol is now complete. Only an HK certified armorer should disassemble the pistol further. P2000 & P2000 SK Pistol Assembly 1. Install the right slide release into the recess located on the right side of the frame and rotate it downward until it is parallel to the top of the frame. Ensure that the tab on the lever is engaged in the recess cutout in the frame and that the lever is them pushed into the frame and rotated downward approximately 45°. 2.
PAGE 15
Magazine Disassembly NOTE: Only P2000 (not the P2000SK or P30) models use widely available USP Compact magazines. A variety of USP Compact magazines are in use, including those with extended and flat floorplates with high capacity and 10-round capacity, USP Compact 9mm magazines with a 13-round capacity and USP Compact .40 magazines with a 12-round capacit y. USP Compact 9mm and .40 S&W magazines with a 10-round capacity are also available. Disassembly of 10-round magazines: 1.
PAGE 16
4. Push the locking plate down into the magazine housing against the pressure of the magazine spring and hold it there. 5. On 10-round magazines, push the floorplate up onto the base of the magazine housing until the locking tabs engage in the sides of the housing. 6. Check to see if the locking tabs on the floorplate are securely locked into the housing and the locking detent on the locking plate fits within the hole in the floorplate.
PAGE 17
Magazine • Gently scrub the top of the magazine, concentrating on the follower and feed lips, using the nylon toothbrush moistened with solvent. • Using a rag and cotton swabs, remove all loose fouling from all surfaces of the magazine. Major Cleaning - Major Cleaning is the same as normal cleaning except that: • The magazine is disassembled for cleaning. • All parts should be rinsed with or immersed in solvent and thoroughly scrubbed with a nylon brush.
PAGE 18
Lock-out device P Series pistols are equipped with a patented HK Lock-Out™ device. This component replaces the lanyard loop insert in the frame and when engaged, locks the handgun’s action by blocking any movement of the trigger, the hammer and the slide. The handgun is locked and cannot fire until unlocked. The Lock-Out control plate is accessible through the pistol’s magazine well (see Figure 30).
PAGE 19
Section 8 Parts List P2000 (.40 S&W, 9 mm, .357 SIG) Item 1 * * * 2 3 4 5 * * * 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 * 30 31 32 33 34 35 36 Description Identification No. Barrel .40 S&W . . . . . . . . . . . . . . . . . . Barrel 9mm x 19 . . . . . . . . . . . . . . . . . Barrel .357 SIG . . . . . . . . . . . . . . . . . . Recoil spring assembly complete .40 S&W (Items 2-5) . . . . . . . . . . . . . .
PAGE 20
Parts List P2000SK Subcompact (9 mm, .40 S&W, .357 SIG) Item Description Identification No. 1 Barrel (9mm x19) . . . . . . . . . Barrel (.40 S&W) . . . . . . . . . . . . . Barrel (.357 SIG) . . . . . . . . . . . . . 2 Recoil spring assembly, complete . . . . . . . . . . . . . . . * Slide, complete (9mm x19) . Slide, complete (.40 S&W) . . Slide, complete (.357 SIG) . . 3 Slide (9mm x19) . . . . . . . . . . Slide (.40 S&W) . . . . . . . . . . Slide (.357 SIG) . . . . . . . . . . .
PAGE 21
Parts List P30 Series Item — 1 2 3 4 5 — 6 7 7.1 7.2 7.3 7.4 7.5 8 9 10 11 11.1 11.2 11.3 12 13 14 15 16 — 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 — — — — — — 41 42 43 44 45 46 Description Identification No. Item Description Identification No. Barrel, complete (Items 1-5) Barrel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 308 Recoil spring, compl. (Items 2-5) . . . . . . . . . 234 319 Recoil spring guide rod . . . . . . . . . . . . . . . .
PAGE 22
Weapon Type ________________ Serial Number ________________ Number of Cumulative Total Maintenance Date Rounds Fired of Rounds Fired Users Name & Remarks ________________________________________________________________________________ ________________________________________________________________________________ ______________________________________________________________________________ ______________________________________________________________________________ _______________________________
PAGE 23
HK USA730900-05302013 HECKLER & KOCH 5675 Transport Boulevard Columbus, Georgia 31907 United States of America Tel: (706) 568-1906 Fax: (706) 568-9151 USA Website: www.hk-usa.com HECKLER & KOCH D-78722 Oberndorf/Neckar Postfach 1329 Germany Tel: 011-49-7423/79-0 Fax: 011-49-7423/2280 Global Website: www.heckler-koch.
